User:Jak/Sandbox2

From DCS World Wiki - Hoggitworld.com
< User:Jak
Revision as of 07:54, 28 May 2021 by Jak (talk | contribs) (Tactical/Support Menu Formats)

Contents

Avionic System Introduction

The F/A-18 avionic system is the computer interface with most of the aircraft systems. This section provides an overview of the displays and inputs used to interact with the avionics.

The avionics displays information to the pilot through the Multipurpose Display Group (MDG). The pilot gives inputs to the system using controls on the MDG as well as the HOTAS.

Multipurpose Display Group

The Multipurpose Display Group (MDG) is the avionic system output to the pilot and the point of pilot-input to the avionics.

The primary flight instrument is the Head-Up Display (HUD), which displays flight instruments in addition to navigation, sensor, and weapon cuing. The Helmet Mounted Display (HMD) duplicates the HUD symbology with some additional capabilities. The left Digital Display Indicator (DDI), the right DDI, and the center Multipurpose Color Display (MPCD) are the main "heads-down" displays and provide the majority of system interfaces. Multifunction pushbuttons on the DDIs/MPCD let the pilot select options. Finally, the Upfront Controller (UFC) located below the HUD and between the DDIs is used for more complicated data entry (e.g. waypoint coordinates) and selecting certain functions as well.

Head-Up Display (HUD)

The Head-Up Display (HUD) is a display projected onto a glass at the front of the cockpit. The projection is collimated, which means the symbology is focused at infinity. This allows symbology to be accurately overlayed on the outside world regardless of the angle and distance from which the pilot is looking at the HUD. This is vital for displaying symbols that represent a real position in 3D space, such as a target on the ground.

There is a large amount of possible HUD symbology. The universal HUD symbology is described under Navigational HUD Symbology.

Helmet-Mounted Display (HMD)

The Helmet-Mounted Display (HMD) is a display fixed to the helmet. Unlike the HUD, the HMD symbology can always be seen regardless of where the pilot is looking. The HMD in the F/A-18 is the Joint Helmet Mounted Cueing System (JHMCS) and these terms are used interchangeably. The nature of the HMD permits some unique functionality. For example, the pilot can see a symbol for a target in the air or on the ground that is outside the field of view of the HUD.

The HMD replicates most symbology found on the Head-Up Display. HMD-unique symbology is specifically described in the appropriate sections. Otherwise, the symbology described for the HUD is applicable also to the HMD, except where noted.

Digital Display Indicators (DDIs)

The multifunction displays for interfacing with most of the aircraft systems are the left and right Digital Display Indicators (DDIs). The center AMPCD has the same functionality.

On the DDIs, as well as the AMPCD, the pilot is able to display many pages or "formats." Formats display information and allow for interfacing and control with various systems.

The DDIs are tri-color with green, yellow, and red capability. The primary color used in the avionics is green. Yellow is associated with a few things like cursors and unknown/ambiguous targets. Red is associated with hostile targets.

There are twenty pushbuttons (PBs) located around each DDI which are used to select a digital label next to that physical button.

Tactical/Support Menu Formats

All the available formats are selected from one of the two main menu formats. These are the Tactical (TAC) Menu and Support (SUPT) Menu formats. In general, the formats on the Tactical Menu are sensor and weapon oriented, while the Support Menu is utility and navigation oriented.

  1. Pushbuttons (PB) - There are 20 pushbuttons (PBs) located around the display. A PB has an associated label for its function depending on the selected format/subformat, etc. The PBs are numbered clockwise as illustrated.
  2. Menu Option - PB18 serves as a universal "return to menu" option. When selected from any other format it invokes the Tactical Menu format. From there it will cycle between the Tactical and Support Menu formats (refer to Menu Formats). Above the pushbutton, with weight off wheels, a four digit system time is displayed for maintenance use. With weight on wheels, it reads MENU.
  3. Cautions - On the left DDI, the caution bank is displayed in large text. Cautions are any critical scenarios the pilot needs to be aware of pertaining to the aircraft systems. Generally this is limited to fuel, electrical, and hydraulic systems. If there are too many cautions they will "spill over" to the AMPCD and right DDI in that order. This order also applies if the left DDI or AMPCD is off.
  4. Advisories - On the left DDI, advisories to the pilot are displayed on this line after the word ADV-. These are non-critical pieces of information pertaining to various systems. New cautions are initially displayed spaced away to the right. When the Master Caution light is extinguished and then pressed again (twice in total), existing advisories "stack" close together to the left. Each advisory is separated by a comma.

Advanced Multipurpose Color Display (AMPCD)

The AMPCD (often called the MPCD) is a multifunction display in the bottom center of the front panel which has identical function to the DDIs. The AMPCD is full-color capable. This is used to (optionally) display a colored background chart on the Horizontal Situation Indicator (HSI) navigation format and the Situation Awareness (SA) air-to-air format.

As there is on the DDIs, there are 20 pushbuttons (PBs) around the AMPCD. (Information about night day knobs etc) The DDI formats are all accessible on the AMPCD.

Upfront Controller (UFC)

Master Modes

Navigation (NAV)

Air-to-Ground (A/G)

Air-to-Air (A/A)

HOTAS Controls

Control Stick

Throttle

Navigation Systems

Navigational HUD Symbology

This section covers the fundamental flight instrumentation and all navigation cuing that can be displayed on the Head-Up Display (HUD). With a few exceptions noted, most of the flight and navigation symbology is common throughout all master modes.

A wide range of weapon and sensor related symbology can also be displayed on the HUD depending on various factors. This symbology is detailed in the relevant sections. Refer, generally, to Air-to-Air Systems and Air-to-Ground Systems.

Basic Flight and Navigation Symbology

HUD - NAV Labels.jpeg
  1. Indicated Airspeed - Indicated airspeed (IAS) in knots is displayed in this box.
  2. Best Climb Airspeed - When CLIMB is boxed on the FPAS format, the best climb airspeed is displayed above the current airspeed. This is only displayed in NAV master mode.
  3. Altitude - Altitude is displayed in feet in this box. When the altitude source switch is set to BARO, barometric altitude above mean sea level (MSL) is displayed. If the source is set to RADAR, radar altimeter altitude above ground level (AGL) is displayed if valid. The radar altitude is always suffixed by a letter R. Radar altitude may go invalid due to steep bank angle or being too high above the ground. When the radar altitude is invalid and the source is set to radar, barometric altitude is displayed instead. This condition where radar altitude is selected but barometric altitude is actually being displayed is indicated by a flashing letter B to the right.
  4. Vertical Speed - Vertical speed in feet per minute (fpm) is displayed directly above the altitude box. A negative value (losing altitude) is prefixed with a minus (-) sign. The vertical speed is only shown in NAV master mode.
  5. Angle of Attack - Current angle of attack (AOA)/alpha is indicated here next to the Greek alpha symbol. The AOA is blanked when the gear is down and the aircraft is "on speed" (AOA between 6.9° and 9.3°).
  6. Mach Number - Current speed as a percentage of the speed of sound (Mach number) is indicated here.
  7. Current G - The current G-force experienced by the aircraft is indicated here.
  8. Peak G - The highest G-force experienced is indicated here if that peak G-force was more than 4.0G. The peak G is reset when the HUD symbology reject switch is cycled to REJ1 (or REJ2) and back to NORM.
  9. Time Window - Either the current Zulu time (abbreviated EI), a countdown timer (CD), or an elapsed time (ET) can be displayed in this area of the HUD. This is configured with the TIMEUFC function on the HSI format.
  10. Velocity Vector - The velocity vector indicates the actual vertical flight path angle and, when uncaged, the horizontal flight path (accounting for wind drift/yaw) as well. When the ghost velocity vector is displayed (caged velocity vector operation), then this velocity vector is displayed near the center of the HUD and does not indicate true horizontal drift. Refer to Velocity Vector Operation. The velocity vector flashes if its position is outside the HUD field of view. A dot appears in the center of the velocity vector when the TDC is assigned to the HUD.
  11. Ghost Velocity Vector - The ghost velocity vector is displayed when the HUD is caged and appears as a segmented version of the velocity vector. Its purpose is to indicate the real horizontal flight path angle of the aircraft with regard to wind drift, while the regular velocity vector remains near the center of the HUD. Refer to Velocity Vector Operation. The ghost velocity vector flashes if its position is outside the HUD field of view.
  12. Flight Path/Pitch Ladder - The flight path/pitch ladder indicates either the true flight path angle (typically) or the nose pitch. Each bar is placed in 5° increments, with angles below the horizon being dashed. For details, refer to Flight Path/Pitch Ladder Behavior. The ladder is always oriented upright relative to the horizon. This is used with the velocity vector, which is always oriented to the aircraft itself, to visualize aircraft roll.
  13. Bank Angle Scale - Aircraft bank angle is indicated by this scale and the triangle caret that moves along it. The ticks are placed on both the left and right sides at 5°, 15°, 30°, and 45° increments. The triangle is limited just past the final tick at 47°. When bank is greater than 47°, the triangle flashes.
  14. Heading Scale - The heading scale indicates the current magnetic or true heading of the aircraft in conjunction with the heading caret. The heading scale can be thought of a compass. It is not to scale; in other words the ticks on it are not scaled to the outside world on the HUD. The heading scale is shifted up 1.25° from its position in NAV master mode when in A/G or A/A master mode.
  15. Heading Caret - This caret simply indicates the current aircraft heading on the heading scale. This does not indicate actual aircraft ground track corrected for wind drift, but only the heading of the nose. When the heading reference is set to true north on the HSI format, the caret becomes a letter "T".
  16. Command Heading Cue - The command heading cue indicates the commanded heading to steer to the selected waypoint/OAP, offset, markpoint, TACAN, or designation. The command heading cue, although commanding a heading, is corrected for wind drift so that flying the commanded heading will place the aircraft's ground track at the desired point and not necessarily point its nose directly at it. As such, using the command heading cue simply involves steering the aircraft such that the heading cue line and the heading caret are lined up. When steering to an A/G designation, the cue becomes a diamond shape.
  17. Navigation Range Cue - Range in nautical miles to the selected steer-to point is selected here. This can be a waypoint/offset aimpoint, offset, markpoint, TACAN, or A/G designation. A waypoint/OAP, offset, or markpoint is suffixed by the letter W (waypoint/OAP), O (offset), or M (markpoint) and its number. A TACAN is suffixed by its three-letter identifier. The A/G designation is suffixed by TGT. Range to anything but TACAN is range over the ground. Range to TACAN is slant range.

Flight Path/Pitch Ladder Behavior

The flight path/pitch ladder on the HUD is typically in fact a flight path ladder, in that it is positioned relative to the velocity vector. The pitch ladder drifts horizontally with the velocity vector. When the HUD is caged, the pitch ladder is aligned with the caged velocity vector so that it remains near the center of the HUD.

Whenever the velocity vector which the pitch ladder is aligned with is outside the HUD field of view (FOV), the ladder shifts to the center of the HUD and is then positioned relative to the aircraft waterline instead. The waterline is indicated by a "W" symbol whenever the velocity vector is outside the HUD field of view. In this scenario, it only indicates pitch relative to the waterline (nose). Note that when the velocity vector is caged, if only the ghost velocity vector is outside the HUD, no change with the flight path ladder occurs since it is aligned with the caged velocity vector. The caged velocity vector will only escape the HUD FOV in extreme yaw/crosswind scenarios in a bank.

The pitch/flight path ladder contains "rungs" in 5° increments. The horizon itself is indicated by a solid line. Angles above the horizon are solid as well, while angles above are dashed. The rungs are slanted toward the horizon by half the amount of the angle which they represent. For example, the -5° line is slanted 2.5° upward (toward the horizon) and the +10° line is slanted 5° downward.

Caged/Uncaged Velocity Vector Behavior

The velocity vector can either be "caged" or "uncaged". In NAV master mode, this can be toggled with the Cage/Uncage button on the throttle. In A/G master mode, the HUD is always caged. In A/A master mode, the HUD is always uncaged.

When the velocity vector is caged, the "regular" velocity vector is horizontally displayed near the center of the HUD (caged). Navigational cuing is referenced to the caged velocity vector. This makes the HUD easier to read at significant yaw or crosswind components. If the true horizontal flight path angle differs from the ghost velocity vector position by more than 2°, a segmented "ghost" velocity vector is displayed to show the real flight path. Both velocity vectors indicate the real vertical flight path angle of the aircraft.

Note that anytime the aircraft is in a bank, the caged velocity vector may not always be precisely on the center of the HUD, but close to it. This is due to the fact the caged velocity vector has to indicate the true vertical flight path angle while also maintaining the same distance from the ghost velocity vector as the distance between the ghost velocity vector and the aircraft waterline/heading.

When the velocity vector is uncaged, only one "regular" velocity vector is displayed which always indicates the true horizontal (and vertical) flight path angle.

Caged Velocity Vector
Caged VV.jpg
Uncaged Velocity Vector
Uncaged VV.jpg

Symbology Reject Modes

HUD symbology can be decluttered, or "rejected", using the switch just under the Upfront Controller (UFC). There are three settings: NORM, REJ1, and REJ2. The following symbology is rejected. All symbology rejected in REJ1 is also rejected in REJ2.

Removed in REJ1 Removed in REJ2
Mach number Heading scale
G-force Navigation range cue
Peak G-force1 Time window
Bank angle scale
Box around airspeed
Box around altitude
Time on target symbology
1 Peak G value is reset when switch is returned to NORM

Landing Symbology

When the landing gear is down and locked, NAV master mode is automatically selected and some changes to the HUD are made. In addition to the symbology illustrated, the Mach, G, and peak G numbers are removed. AOA is also removed when the velocity vector is within the AOA bracket.

HUD Gear Down Symbology.jpeg
  1. Elongated Horizon Line - When the gear is down, the horizon line is elongated as such.
  2. Angle of Attack Bracket - The angle of attack (AOA) bracket indicates the optimal region of AOA for landing. The bracket is positioned relative to the velocity vector. For details refer to Angle of Attack Bracket. Note that the actual AOA readout on the HUD is blanked when the velocity vector is within the AOA bracket.
  3. Waterline Symbol The aircraft waterline is indicated by this "W" symbol whenever the gear is down or otherwise whenever the velocity vector is outside the HUD field of view. The waterline is essentially the nose reference of the aircraft; it indicates aircraft pitch rather than the actual vertical flight path angle, which is indicated by the velocity vector. The waterline symbol is coincident with the tops of the airspeed and altitude boxes which can be used for reference since the waterline symbol is not displayed most of the time when the gear is up.

Angle of Attack Bracket

The angle of attack bracket, or "E" bracket, is displayed when the gear is down. It is horizontally aligned with the velocity vector and vertically positioned to visualize AOA relative to the velocity vector. When the HUD is caged it is aligned with the caged velocity vector.

The AOA brackets represents 6.9°–9.3° AOA. The middle mark indicates 8.1°, which is the precise "on speed" AOA for landing. The AOA bracket serves as an easy means of getting "on speed" for landing. The typical technique is to pitch trim the aircraft such that the velocity vector is fixed at the 8.1° mark.

When AOA is between 6.9 and 9.3° (i.e. the velocity vector is inside the E bracket), the AOA number on the HUD is removed as an indicator of being near on speed AOA.

9.3° AOA
AOA slow.png
8.7° AOA
AOA slightly slow.png
8.1° AOA
AOA on speed.png
7.5° AOA
AOA slightly fast.png
6.1° AOA
AOA fast.png

Courseline Steering Symbology

When a courseline is defined with the courseline switch, a course deviation indicator is displayed near the velocity vector. Note that command heading cue is still displayed on the heading scale to indicate the direct course to the steer point.

For details on the courseline steering mode and the cuing on the HSI format, refer to HSI Courseline Steering Cues.

COURSE DEVIATION SYMBOLOGY PIC.

  1. Course Deviation Arrow - This arrow is positioned relative to the velocity vector to indicate the aircraft's position from the courseline. When the arrow is aligned with the velocity vector the aircraft is on course. When the velocity vector is right of the arrow, the aircraft is right of course, and vice-versa.
  2. Course Deviation Marks - Two dots are displayed along where the arrow moves to indicate the actual deviation from the courseline. The outer dot indicates 8° and the inner dot indicates 4°. The arrow does not move past the outer dot, so at deviations more than 8° the arrow will be pinned to the outer dot.


COMPARATIVE COURSE DEVIATION PICS.

ICLS Steering Symbology

The following steering cuing is displayed when Instrument Carrier Landing System (ICLS) steering is boxed at PB11 on the HSI format.

ICLS SYMBOLOGY PIC.

  1. Course Deviation Line - This vertical line is positioned with the velocity vector (except when outside the HUD field of view). When the line and velocity vector are aligned, the aircraft is on the lateral ICLS course. When the velocity vector is left of the line, the aircraft is left of course and vice-versa. If the velocity vector is outside the HUD field of view, the course deviation line is displayed relative to the waterline symbol.
  2. Glideslope Deviation Line - This horizontal line is positioned with the velocity vector (except when outside the HUD field of view). When the line and velocity vector are aligned, the aircraft is on glideslope. When the velocity vector is below the line, the aircraft is lower than the glideslope, and vice-versa. If the velocity vector is outside the HUD field of view, the glideslope deviation line is displayed relative to the waterline symbol.

COMPARATIVE ICLS PICS.

Time on Target (TOT) Symbology

When the time on target (TOT) function is configured on the HSI format, symbology is displayed just under the airspeed box on the HUD to easily meet the required time on target ground speed. Refer to Time on Target (TOT) Function.

HUD - Time on Target Symbology.jpg
  1. Current Ground Speed Caret - This caret indicates the current aircraft ground speed relative to the required ground speed cue. When the caret is left of the line, the aircraft is slower than the required groundspeed, and vice-versa. The deflection of the caret is ±60kts; as such, the caret is pinned to the left or right side of the airspeed box when slower or faster than the required groundspeed by 30 knots or more. Note that due to the caret indicating ground speed, the change in ground speed may not be 1:1 with the change in the indicated airspeed.
  2. Required Ground Speed Cue - This line indicates the required ground speed relative to the current ground speed caret.


30+ knots slow
TOT slow.png
15 knots slow
TOT slightly slow.png
On TOT speed
TOT on speed.png
15 knots fast
TOT slightly fast.png
30+ knots fast
TOT fast.png

Horizontal Situation Indicator (HSI) Format

The Horizontal Situation Indicator (HSI) format is the primary format for navigation. Typically the HSI is displayed on the central MPCD, which has full color capability to display a chart in the background of the top level HSI format.

The HSI format can be displayed via HOTAS on the MPCD by pressing the Sensor Control switch aft when the format on the MPCD cannot accept TDC assignment. An additional function allows the HSI and Situation Awareness (SA) format to be swapped (on any format). With the TDC already assigned to the HSI/SA, pressing the Sensor Control switch in its direction will cycle between the HSI and SA formats. The SA format is an air-to-air target display with some duplicated HSI symbology. Refer to SA Format.

Top Level HSI Format

HSI Legend

Format Orientations

At the MODE option at PB3, the Track Up (T UP), North Up (N UP), and Decentered (DCTR) orientations are selectable. Track up is selected by default.

Track Up (T UP) / North Up (N UP)

The Track Up and North Up orientations are similar. Both are a 360° view centered on the ownship aircraft symbol. In Track Up, the ownship track over the ground (not necessarily ownship heading) is always oriented at the 12:00 position on the format. Note that the ownship symbol is oriented toward heading, not ground track. In North Up, the north direction is oriented at 12:00 regardless of ownship track or heading.

Picture of Track Up. Picture of North Up. Same scenario.

Decentered (DCTR)

The Decentered (DCTR) orientation is different from the other orientations in that the HSI is not centered on ownship. When Decentered, ownship is placed at the bottom of the format (and centered horizontally). The HSI only covers 80° total in DCTR and is oriented to track up. The range scale setting is doubled, but is still measured from ownship to the compass rose. The same total area is displayed, with double the distance displayed ahead of ownship as in Track Up or North Up modes. This is the main advantage of the Decentered orientation.

Picture of Decentered.

Map Slew Function (SLEW)

HSI Courseline Steering Cues

TIMEUFC Function

HSI Data Sublevel

Waypoint Data Sublevel

TACAN Data Sublevel

Map Data Sublevel

Aircraft Data Sublevel

Flight Performance Advisory (FPAS) Format

Navigation Equipment

Tactical Air Navigation (TACAN)

Instrument Carrier Landing System (ICLS)

Automatic Direction Finder (ADF)

Automatic Flight Control System (AFCS)

Automatic Throttle Control (ATC)

Inertial Navigation System (INS)

Inflight Alignment (IFA)

Ground Alignment (GND)

Stored Heading Alignment (STD HDG)

INS Alignment HSI Format